超聲波清洗機安全操作規程_潔升超聲波清洗機
瀏覽： 發布日期：2019-08-28
1 cleaning scale
1.1 This machine is a special person specializing in equipment, others may not operate without authorization.
1 清洗規模
1.2Ultrasonic cleaning machine is used for secondary cleaning of parts. Uncleaned parts must not be put into the machine for cleaning. 1.3 The scale of cleaning of the machine: engine parts such as engine block, cylinder head, crankshaft, camshaft, connecting rod piston, air compressor, bearings, steering gear, transmission shaft and gear, reducer gear, etc. 2 Operation method
1.1本機為專人專管設備，其他人不得擅自操作。
2.1 The appropriate clean water is taken in the cleaning tank, and the liquid level is determined by the immersed side vibrating box.
1.2超聲波清洗機用于零部件的二次清洗，未經清洗過的零部件不得放入本機清洗。 1.3本機清洗規模：發動機缸體、缸蓋、曲軸、凸輪軸、連桿活塞、空壓機等發動機零部件，軸承、方向機、變速器的軸及齒輪、減速器齒輪等。 2 操作方法
2.2 Close the power switch on the rear panel of the control cabinet, start the electronically controlled heating switch, and point the white scale line on the water temperature adjustment knob to the appropriate temperature, usually 50 ° C \u0026 mdash ^ fen ^ 55 ° C in winter and 60 ° C - 65 ° C in winter. . The maximum temperature of the cleaning solution must not exceed 70 °C during use.
2.1清洗池內參加恰當清水，液面高度以浸沒側振盒為準。
2.3 First wash the cleaning agent with warm water in a water bucket and mix well to dissolve it. When the water temperature in the cleaning tank rises to 40 °C, it will participate in the water tank. The cleaning agent is diluted with 1-2% water (about 5 to 9 kg of cleaning agent).
2.2合上控制柜后面板上的電源開關，發動電控加熱開關，將水溫調節旋鈕上的白色刻度線指向恰當?shù)臏囟?，通常夏天?0℃—55℃冬天為60℃－65℃。在使用過程中，清洗液最高溫度不得超過70℃。
2.4 Place the parts in the net basket and put them into the cleaning tank quietly. The cleaning parts should be turned on more than 60% of the cleaning tank to prevent whistling and damage the power supply.
2.3先用水桶將清洗劑用溫水沖開攪勻，使其充沛溶解，待清洗槽水溫升至40℃擺布時參加水槽中。清洗劑按1～2%兌水稀釋?zhuān)ㄇ逑磩┘s5～9公斤）。
2.5 After the water temperature reaches the reserved value, start cleaning, turn the ultrasonic bottom and side power knob clockwise to the maximum, press the ultrasonic start button, and the cleaning starts. To stop cleaning, press the ultrasonic abort button directly.
2.4將零部件置于網筐中悄悄放入清洗池內，散布均勻。清洗零件應達清洗槽內60％以上再開機，防止嘯叫，損壞電源。
2.6 punctual cleaning: first set the cleaning time, set the punctual switch to the open position, then turn the two power knobs clockwise to the maximum, press the ultrasonic start button to start cleaning, after the punctual time, the ultrasonic power supply will be actively closed.
2.5水溫到達預訂值后開機清洗，將超聲波底部與側部功率旋鈕順時針旋至最大，按下超聲波發動按鈕，清洗開始。若要中止清洗，直接按超聲波中止按鈕。
2.7 After cleaning, the ultrasonic power supply should be enclosed, and then the cleaned parts should be taken out, and the residual cleaning liquid in each channel should be completely blown out with compressed air, and the appearance should be dried.
2.6守時清洗：先設定清洗時刻，將守時開關置開位，再順時針將兩功率旋鈕旋至最大，按下超聲波發動按鈕清洗開始，到達守時時刻后，超聲波電源將主動封閉。
2.8 If there is too much oil on the surface of the cleaning tank, it should be turned off by overflowing the equipment to prevent secondary pollution of the workpiece being cleaned. 3 Notes
2.7清洗結束后要封閉超聲波電源，再取出清洗好的零部件，用壓縮空氣將各孔道中的殘留清洗液完全吹盡，并將外表吹干。
3.1 After placing the workpiece, the water level of the washing machine sink shall not be lower than the side vibration plate. Take care when handling the workpiece to prevent violent bumps.
2.8若清洗池液面上存有過多油污，應翻開溢流設備將其掃除，以防被清洗工件的二次污染。 3 注意事項
3.2 The following conditions shall not be used to open the ultrasonic power supply: when the new cleaning liquid is used, the horizontal level of the cleaning liquid is greatly shaken; when the cleaning material is taken in and taken out; during the cleaning operation, the cleaning tank is aborted and the cleaning tank transducer is no noise.
3.1放入工件后，清洗超聲波清洗機價格機水槽的水位不得低于旁邊面振板。放取工件時要輕拿輕放，防止劇烈磕碰。
3.3冬天槽體內液體不能結冰，使用前先加熱再發動超聲波（25℃以上為佳）。
3.2以下情況不得敞開超聲波電源：新參加清洗液，清洗液水平面有較大動搖時；參加和取出清洗物時；清洗作業中，俄然中止，清洗槽換能器無噪音時。
3.4不得將沸水直接參加清洗槽內，應常常定時整理清洗槽底部?jī)?nèi)的污泥，以防底部換能器過熱而掉落損壞。
3.3冬天槽體內液體不能結冰，使用前先加熱再發動超聲波（25℃以上為佳）。
3.5接連作業時，如過熱，機器將主動中止，冷卻系統照舊作業，待降止適宜溫度時，機器降主動敞開超聲波。
3.4不得將沸水直接參加清洗槽內，應常常定時整理清洗槽底部?jī)?nèi)的污泥，以防底部換能器過熱而掉落損壞。
3.6禁止從超聲波控制柜進風口處濺入導電液體（如水）。 4 保護與養護
3.5接連作業時，如過熱，機器將主動中止，冷卻系統照舊作業，待降止適宜溫度時，機器降主動敞開超聲波。
4.1應常常查看控制柜與清洗槽的接地情況，必須接地杰出。
3.6禁止從超聲波控制柜進風口處濺入導電液體（如水）。 4 保護與養護
4.2電源進線、控制柜與清洗槽之間連線插頭應定時查看是不是連接可靠以及絕緣性與導電性。 4.3堅持機器內部各部件的清洗，不使用時封閉電源總開關。 4.4清洗液應及時沉積、過濾或替換，以保證清洗作用。 4.5防止對機器的磕碰或劇烈轟動。
